Electro-cam PS-6144 Series Manual do Utilizador Página 76
- Página / 112
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
6-4 Communications
Serial Commands
Description The PS-6144 controller recognizes a set of 95 commands. Some of these commands
involve testing and diagnostic functions performed at the factory. Because these com-
mands are of little use in field installations, they are not included in the following pages.
For information on the complete command set, contact the factory.
The commands are grouped by general function. In the syntax shown for each com-
mand and reply, the characters used for STX, ETX, ACK, and NAK are substituted, as
listed on the previous page.
The commands are listed in hex.
CMD
(hex) Name Function
04 Hello Are you there?
Cmd: ! ADR 04 CSM <CR>
Reply: A <CR>
06 Com Stop Stop operation & idle; changes will be written directly to
EEPROM with no other action taken.
Cmd: ! ADR 06 CSM <CR>
Reply: A <CR>
07 Checksum Sets new checksums in EEPROM.
Cmd: ! ADR 07 CSM <CR>
Reply: A <CR>
08 Start Resume operation.
Cmd: ! ADR 08 CSM <CR>
Reply: A <CR>
09 Reset Create hard reset through watchdog.
Cmd: ! ADR 09 CSM <CR>
Reply: A <CR>
0A RPM Current RPM.
Cmd: ! ADR 0A CSM <CR>
Reply: A XXXX CSM <CR>
where “XXXX” = current RPM in hex.
38 Shaft Pos Shaft position.
Put: ! ADR 38 P XXXX CSM <CR>
Reply: A <CR>
Get: ! ADR 38 G CSM <CR>
Reply: A XXXX CSM <CR>
where “XXXX” is the shaft position in hex.
0B Grp Pos Current position.
Cmd: ! ADR 0B XX CSM <CR>
Reply: A YYYY CSM <CR>
where “XX” is the group number minus one. “YYYY” is that
group’s position in hex.
Supervisory
Commands
Status
Commands
- PS-6144 Series 1
- Table of Contents 3
- Mechanical Cam Switches 5
- Programmable Limit Switches 5
- PS-6144 Description 6
- Basic Terminology 7
- PS-6144 Standard Features 7
- PS-6144 Optional Features 8
- General Mounting & Wiring 9
- PGM:1 RPM:1500 10
- MENU< POS: 180 10
- 2-3 Installation & Wiring 11
- 2-4 Installation & Wiring 12
- Controller Input Wiring 13
- 2-6 Installation & Wiring 14
- 2-7 Installation & Wiring 15
- Output Wiring 16
- Output Wiring (cont’d) 17
- Keypad Wiring 20
- DIP Switch Configurations 21
- Communications Wiring 23
- Resolver Installation 24
- Resolver Dimensions 25
- Resolver Cables 26
- Output Transistor Replacement 28
- Menu Tree 30
- Initial Programming 31
- OFFSET 3-16 31
- Analog Module Numbe 32
- Analog High RPM 32
- Analog Offset 32
- Number of Analog Output 33
- Communications 34
- Channel Copy 34
- Communications (Cont’d) 35
- Default Program 35
- LEVEL: OPERATOR 36
- PASSWORD: 1234 36
- Password Number 36
- View Program 37
- --- --- --- Program 37
- Enable Codes (cont’d) 37
- GROUP POSITION 38
- DISPLAY: EACH< 38
- Machine Speed 39
- Active Program 39
- Keyboard Quantity 40
- Input Status 40
- Motion ANDing 42
- Memory Tests 42
- Motion detection leve 43
- High RPM setpoint 43
- Low RPM setpoint 43
- Value for this Group 44
- 3-17 Programming 45
- Output Enable ANDing 46
- Output Groups 46
- Output Groups (Cont’d) 47
- Output Status 47
- Password 48
- Output Status (Cont’d) 48
- Password (Cont’d) 49
- Per Channel Enable 49
- Program Copy 49
- Pulse Copy 50
- Program Select Mode 50
- Pulse Copy (cont’d) 51
- Rate Setup 52
- SCALE 53
- FACTOR: 360< 53
- Program to view or modify 54
- Setpoints (Cont’d) 55
- CH:1 EDG 55
- Output Channel 56
- Speed Compensation (cont’d) 57
- Speed Comp Mode 57
- Timed Outputs 58
- Toggle RPM 58
- 4-1 Speed Compensation 59
- Standard Speed Comp 60
- Standard Speed Comp (Cont’d) 61
- Leading Trailing Speed Comp 62
- 4-5 Speed Compensation 63
- Speed Comp Guidelines 64
- Negative Speed Compensation 64
- Mode 1 Operation 67
- Mode 0 Operation 67
- Mode 2 Operation 68
- Mode 1 Operation (Cont’d) 68
- Mode 2 Operation (Cont’d) 69
- Mode 3 Operation 69
- Mode 4 Operation 70
- Mode 3 Operation (Cont’d) 70
- Mode 4 Operation (Cont’d) 71
- Mode 5 Operation 71
- Mode 5 Operation (cont’d) 72
- 6-1 Communications 73
- PLuSNET II Program (cont’d) 74
- 6-3 Communications 75
- Serial Commands 76
- Serial Commands (cont’d) 77
- Output group offset value 80
- Shaft position offset 80
- Checksum 84
- Error Codes 84
- 6-13 Communications 85
- 40279 Offset Mapping 86
- Motion Detection 86
- 40289 Analog High RPM 86
- Quick Reference 86
- 40310 Analog Quantity 87
- Discrete I/O 88
- Registers 89
- Registers (Cont'd) 90
- 40280 Group Index 91
- 40281 Group Offset 91
- 40288 Analog Offset 92
- 40308 Shaft Position 93
- 40309 Shaft Offset 93
- Bit 5: Motion detection 95
- Special Functions 98
- Controller Diagnostics 99
- Keypad Diagnostics 100
- ERROR: RESOLVER 101
- NOT CONNECTED! 101
- General Troubleshooting 102
- 7-5 Troubleshooting 103
- Fuse Part Numbers 104
- PS-6144 Controller Specs 105
- A-2 Appendix 106
- Resolver Specifications 107
- Factory Defaults 107
- A-4 Appendix 108
- Access Codes, Entering 3-20 109
- Analog Output 3-4 109
- Group Position Display 3-10 109
- Offset, Analog Output 3-4 110
- I-3 Index 111
- PRINTED IN U.S.A 256 10/01 112
Manuais e produtos relacionados com Routers Electro-cam PS-6144 Series
Routers Electro-cam 5000 Series Manual do Utilizador
(80 páginas)
(80 páginas)
Routers Electro-cam PL-1746 Manual do Utilizador
(8 páginas)
(8 páginas)
Routers Electro-cam PL-1746 Series Manual do Utilizador
(146 páginas)
(146 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais